Recipio '14 writing-desk

Product Codes

Writing-Desk

LXC5

LXC5_D

LXC5_S

Warnings

Keep for reference: read carefully.

Always remember to be careful not to use the product improperly, considering its designated functions.

When the product is no longer used, do not abandon it, but take it to a suitable public waste collection facility.

To maintain the quality and finish of the surface, it is advisable to use protective articles (e.g. placemats or trivets) under objects that could scratched it.

This product sheet complies with the legal obligations pursuant to the "Consumer Code" Decree n. 206 dated 6/9/2005 and the "Actuation Regulation" Decree n. 101 dated 8/2/1997.

Materials

Top
structural expanded polyurethane foam

Top section
steel sheet covered in leather

Support frame
solid wood

Crosspiece protection
aluminium

Ferrules
felt

Maintenance

Wood - Painting

For weekly maintenance, dust the surface with a dry cloth.
For dried dirt, use a well-squeezed out cloth, damp with warm water.
For greasy or oily dirt, use a damp sponge and dish washing detergent, and then wipe with a well-squeezed out cloth damp with warm water.
Warning! Apply the detergent directly on the damp sponge, and never on directly on the furniture.
Do not exert excessive pressure and always follow the grain on wood furniture.
Note that if you press or rub too hard, surfaces can become 'polished'.
Avoid using abrasives and products containing solvents, ammonia and/or alcohol.
Make sure to dry the surfaces completely after washing.

Shellac

Easily scratched. Be very careful with this finish.
For weekly maintenance, dust the surface with a cloth.
For dried dirt, use a well-squeezed out cloth, damp with warm water.
For greasy or oily dirt, use a sponge damp with warm water and dish washing detergent, and then wipe with a well-squeezed out cloth damp with warm water.
Warning! Apply the detergent directly on the damp sponge, and never on directly on the furniture).
Do not use excessive pressure and always follow the satin finish grain.
Note that if you press or rub too hard, surfaces can become 'polished'.
Avoid using abrasives and products containing solvents, ammonia and/or alcohol.
Make sure to dry the surfaces completely after washing.
Our Stores and dealers sell the specific 'Kit for shellac maintenance and cleaning' by B&B Italia (code SETPGM), which contains a detergent suitable for the protection and cleaning of your product’s shellac finish.

Aluminium

We advise using normal commercial products for cleaning delicate surfaces and/or warm water and neutral soap.
Never use abrasives or products containing solvents, ammonia and/or alcohol.
Make sure to dry the surfaces completely after washing.

Cover (Alfa, Beta, Gamma, Koto leather)

For regular cleaning, we recommend a weekly dusting with a soft cotton cloth. If the cover is stained, promptly remove the cause and dry the affected area.
Finally, wipe with a sponge dampened with water and mild detergent (or water and milk).
Wipe with a gentle circular motion and work from the outside of the stain toward the inside.
The action should be more like a skin massage than mechanical rubbing.
Before applying any product over broad areas, it is advisable to test the effectiveness of the procedure by applying the product on a small, hidden area, even though the product may be specifically designed for the material.
After cleaning, apply a solution of water and milk to restore the protective qualities and softness of the leather.
Remember that leather treated with aniline is highly absorbent and may require more frequent cleaning when subjected to heavy-duty use in high-traffic areas.
Two or three times a year, we recommend applying products included in the 'Kit for leather maintenance and cleaning' by B&B Italia (code SETPN) using a soft cloth. The kit is available from our Stores and dealers.

Designer

Antonio Citterio

Antonio Citterio was born in Meda (Milano) in 1950, and started his design office in 1972, graduating in architecture at the Politecnico di Milano in 1975. Between 1987 and 1996 he worked in association with Terry Dwan and, together, they designed buildings in Europe and Japan.

In 2000, with Patricia Viel, he founded a practice for architecture and interior design, developing international complex long-term projects, at all scales and in synergy with a qualified network of specialist consultants. The studio has today taken the name of "Antonio Citterio Patricia Viel". Antonio Citterio currently works in the industrial design sector with numerous Italian and foreign companies. In 1987 and in 1994 he was awarded the Compasso d’Oro-ADI. From 2006 to 2016 he has been professor of Architectural Design at the Mendrisio Academy of Architecture (Switzerland). In 2008 he was honoured by the Royal Society for the Encouragement of Arts, Manufactures & Commerce of London, which gave him the title of “Royal Designer for Industry”.

Antonio Citterio is art director of Maxalto, Arclinea and Azucena.